View all posts

NEW Nizo 2.7 Volt lightmeter power circuit

Posted on by digitalsuper8

2.7 Volt lightmeter power board for Nizo super8 camera

Presenting the latest solution for a 2.7Volts regulator circuit, to create a permanent solution for powering the lightmeter of the Nizo 8xx/5xx/4xx family of super8 cameras. These cameras normally require 2 buttoncell batteries of 1.35V each, which are hard or nearly impossible to come by nowadays.

We developed a new solution, on a dedicated tiny printed circuit board (10mm x 10mm), with only 3 components. It can be connected to the main battery supply of the super8 camera, and it supplies a rock-solid, constant 2.7 Volt output voltage that can be connected to the light meter circuit.

The circuit is designed around a dedicated voltage regulator IC. Packaged in a small SMD design this IC allows for a very small board design. Complemented with 2 capacitors the circuit board is a mere 10mm x 10mm in size. As a result it allows easy placement into the button-cell light meter battery container.

See this video for explanation and example installation of the regulator board into a Nizo 801 Macro super8 camera:

installing the Digital Super8 Lightmeter Power Board in a Nizo Super8 camera

The board has GND (black wire soldered to pad) and Vin (red wire soldered to pad) inputs and one Vout 2.7Volt output (the camera 2.7V lightmeter wire (usually yellow in Nizo’s) can be soldered to it). The EN pad can be left unconnected.

It is strongly advised to ensure that precautions are taken to isolate the board electronically to prevent short-cuts to ground. This is because the metal parts of the camera and the button-cell battery container cover are connected to ground. Using the provided shrink tube is advised.

Code improvements

Posted on by digitalsuper8

Earlier in 2021 we finally solved some major software stability issues. The C++ code that runs on the Nanopi Neo Air inside the cartridge was crashing relatively often during shooting. Causing loss of captured images.

After long research we found out that this was caused by an imagefile write (the captured image) and an image file read (an image file to monitor the captured result in real time).

By changing the setup of the system, making the Nanopi run its code from fixed eMMC memory (on board the Nanopi) and writing the RAW files to its separate microSD card we achieve that the monitor files are read off of the eMMC memory while the RAW files are written to the MicroSD. Thus avoiding memory acces issues and subsequent code crashes due to a segmentation fault.

we now feel confident to continue developing the Digital Super8 Cartridge with software that is reliable enough for the user.

Note: the Digital S8 Cartridge runs on C++ code, while it also has its own WiFi accesspoint and webserver on board. This allows users to run our HTML5 app on their iPhone or smartphone to have full cartridge control and monitoring functionality.

Code update: lighter code, monitoring in color

Posted on by digitalsuper8

In an effort to improve the code performance we did a lot of weeding out stuff from the DigitalSuper8 cartridge C++ code. We simplified the code quite a bit and also used Mutexes to prevent multiple threads from trying to alter or test certain variables at the same time. Seems that errors have lessened but more testing is required.

New: Color monitoring while filming
Importantly we managed to ‘upgrade’ functionality with color image monitoring while shooting raw images. It used to be B&W for performance purposes.

Safer multi threading and queuing
Also we are using the Qt framework which is a C++ library framework with added functionality such as threadsafe communications between objects. We changed the code so as to send ‘Mat’ arrays that contain the captured images (using OpenCV libraries for that) from one thread to another, that way achieving a safer queuing mechanism as well.

Monitoring explained
As further Information: the Digitalsuper8 cartridge runs it’s own webserver and WiFi accesspoint so that a user can fully control the functions and settings of the cartridge and can monitor the captured frames in real-time through a browser on a smartphone or iPhone.

How this real-time monitoring works:

Next to capturing and storing RAW images from the Ximea subminiature camera and sensor in the cartridge, the cartridge sends image file names for each captured and written frame to the browser via server sent events. The browser uses that file name info to load the image and display it on the smartphone. So the videostreaming solution is actually a frame by frame retrieving of images at 18 fps by the browser, triggered by server sent events

Cleaning the audio heads of Bauer T610 Super8 projector

Posted on by digitalsuper8

Here’s a short tutorial on how to clean the magnetic heads of the Bauer T610 Stereo Super8 film projector. This tutorial is also largely applicable to the T502.

Step 1: open the projector by taking off the front cover. Simply by pulling it away.

pulling away the cover

Step 2: Turn the control knob to its ultimate left turn position, the ‘maintenance’ position.

control knob to ultimate left turn position

Step 3: remove light bulb and light bulb holder (to create space to work).

Step 4: It’s smart to cover the sliders with a piece of paper so that screws and small parts cannot fall into the ‘mixer’ part of the projector.

piece of white paper covers the sliders

Step 5: unscrew the clamp of the first magnetic head, which is the ‘erasure’ head. Take it out. Be very careful: when unscrewing the clamp make sure the screws don’t fall into your projector! Also there is a thin sheet of metal that stays behind in the holder of the magnetic head. Just leave it in place. If by chance it comes out together with the head, make sure to put it back in.

viewing the heads from above
removed audio clamp
Dirty magnetic eraser head

Step 6: clean the head with a cotton tip and some cleaning alcohol (spiritus or similar). And put it back in place. Careful to not lose screws.

Clean head

Step 7: unscrew the clamp of the second magnetic head, the recording and playback head. Similar to the first head: take it out and clean it. Be mindful of the thin metal sheet that is inside the head holder.

unscrewing the clamp
The playback and recording head, note the left and right track pick up elements.
Cleaned head
Dirt and iron residue removed

Step 8: After having put back in place the cleaned playback/recording head, repeat the procedure for the third and final head, which is the ‘monitoring’ head. This head is used for monitoring the audio for example ‘live’ when recording audio with the recording head. The sound lags some 4 frames behind.

Finishing up: after cleaning the monitoring head put it back in place. Put the bulb holder and bulb back in place, close the cover and voilà: you have a Bauer projector with clean heads, able to record and playback crisp

Smartphone App for Digital Super8

Posted on by digitalsuper8

So we’re working hard on the Digital Super8 app for smartphones. To fully control the Digital Super8 cartridge and all settings. To provide monitoring while filming as well as when doing trial shots without actual recording. And to allow viewing the footage you shot.

The Digital Super8 cartridge sets up its own WiFi access point for your smartphone to connect to and then through the app you fully take control, while you’ve got the cartridge slid into your Super8 camera.

At this time we’re ironing out some minor challenges to increase the performance of the monitoring and viewing of captured shots. Using multi-threading to ensure that the RAW images get displayed in full color and smoothly.

Stay tuned.

NanoPi Neo Air in Digital Super 8 Cartridge

Posted on by digitalsuper8
We managed to port our Digital Super 8 code to the NanoPi Neo Air. Using Qt and Qt Creator for platform independent development this wasn’t such a big task, fortunately. Also we managed to get the NanoPi Neo Air to boot up, set up a Wifi access point (SSID: DigitalSuper8 :-)), and to start VNCserver which allows a user to view the desktop of the NanoPi in a smartphone or IPhone. Also the Digital Super 8 control and monitor application is started and can then be viewed via WiFi on the smartphone.
That’s actually quite cool!
Having the NanoPi Neo Air act as a WiFi accesspoint, while running the Armbian OS on it was the most complex task and we had to re-write some scripts to nail it.
Now we are waiting for the new 3D printed cartridge to arrive. It is designed and printed by Dutch 3D print company http://www.partsondemand.eu. The new cart will allow build in of NanoPi, sensor and trigger synch circuit board, LiPo battery (1200 mAh), and charger/booster circuit. The device will have status LED, microUSB charger port, USB port for copying captured images to USB stick, microSD port for option to exchange microSD with updated image.
The device boots from and runs on 32GB eMMC, which enables the fastest RAW image writing and performance.

Parts list of the digital super-8 cartridge

Posted on by digitalsuper8

To provide more information about our Digital Super-8 Cartridge solution we publish the ‘bill of materials’. This is for the version with external module. Development is underway for a new prototype with no external module, it will have all electronics inside the cartridge.

Bill of materials:

The Cartridge: 3D printed Super8 cartridge, Ximea MU9-MBRD subminiature camera (with Aptina MT9P031 sensor), our own designed shutter sync circuit PCB with photodetector for film claw detection, microUSB breakout board with image capture indication LED, IR Filter, connector cable from PCB to microUSB board, high quality USB cable to connect cart to external module.

External module: Raspberry Pi3, 32GB SanDisk microSD card, Raspberry Pi touch screen with plastic casing, 6600 mAh power bank with microUSB cable to power the module.

Code: C++ application designed built on Qt Creator to control the capturing, settings, and to develop raw images into video, colorgrading.

Digital Super8 Cartridge footage in HD

Posted on by digitalsuper8

We shot some new footage to test the quality of the Digital Super8 Cartridge. Our software app takes the RAW Bayer images of the cartridge and performs S-Log encoding before we do any further processing. Using the Digital Super8 application we added contrast with S-curve and then applied individual S-Curves on the RGB channels to add warmth. Because Digital Super8 consists of individually captured 12 bit RAW images (global shutter) there’s a lot of flexibility in how to process afterwards. One could do B&W, natural color, warm, cool or whatever else. Also the software provided allows for export of TIFF image format.

The Nizo 801 Macro we used has some motor instability, leading to a bit of flicker.

All electronics inside the Digital Super 8 Cartridge

Posted on by digitalsuper8

We’ve got a working prototype of the Digital Super 8 Cartridge that runs with the Raspberry Pi 3 in an external module with touch screen. Benefits of that solution is the high level of control of operating the Digital Super 8 Cartridge and its settings through the touch screen. Plus the additional real-time monitoring of what is being filmed (in B&W) is a plus.

However the drawback is that the ‘filmtype viewing pane’ of the super 8 camera has to be knocked out of your camera in order to enable the USB connection from the cartridge to the external module.

Some people have suggested to us to try and fit all electronics into the cartridge. Clearly we had to find a smaller Single Board Computer than the Raspberry Pi. Ports and test with the NextThing Co. C.H.I.P. SBC failed as this single core ARM SBC is simply not powerful enough. Now our hopes are on the Orange Pi Zero, which sports a quad-core ARMv7 SOC in a tiny form factor. We have ported the software and the OPI Zero performs reasonably well. Great results for VGA and QHD resolutions. But we need to find optimisations in the code and push for the 720p to runs without dropping frames as well. Whether this will be at all possible we don’t know yet.

Orange Pi Zero inside the Digital Super 8 Cartridge

Benefits of this solution is that the Digital Super 8 Cartridge can simply be dropped into your camera and you don’t have to work with external module or screen. However the cartridge will have to provide a few buttons and LEDs for powering on/off and controlling settings. Alternatively we are looking at using VNC to provide connection via WiFi to your smartphone where you can then see the desktop of the Digital Super 8 cartridge and control its settings.

We are now waiting for the appropriate Lithium Polymer battery and boost/charge circuit and first need to get all the electronics really to fit within the cartridge. More to follow.